Protocol 58 of 81Layer 7FrameAssembly v3.1.2
llms-full.txt
rtpReal-time Transport Protocol Audio & Video Streams

Voice Media Streams & DSCP 46 EF Queue Checks (phone1 <-> phone2 rtp)

Default Port / Protocol
UDP 5004
Host Endpoint Rule
Dual-Stack IPv4/IPv6
Wireshark Display Filter
rtp
Standards & Specs
RFC 3550, RFC 3551, RFC 4733
Wire Stack:Ethernet II[802.1Q / QinQ / MPLS]IPv4 / IPv6UDP 5004RTP (Media)

What It Does on the Wire

SIP sets up the call and rtp carries the actual voice packets — tack dscp 46 (EF) and wait 20ms onto G.711 pt 0 frames to verify your WAN routers aren’t dropping voice into best-effort queues.

Real-time Transport Protocol (rtp, RFC 3550) carries live VoIP voice (G.711, Opus), WebRTC video (VP9, H.264), and IP camera streams over UDP (default dstport 5004). Every RTP packet begins with a 12-byte RTP v2 (0x80) header containing the 1-bit marker, 7-bit Payload Type (pt), 16-bit seq, 32-bit media sample timestamp, and 32-bit Synchronization Source (ssrc).

Combining rtp with FrameAssembly’s precision wait clock (wait 20ms for standard 50-pps G.711 audio, or variable delays to simulate WAN jitter) and dscp 46 (Expedited Forwarding) lets you test QoS queues and Wireshark RTP Stream Analysis with microsecond accuracy.

Test Switch & WAN Router QoS (dscp 46 EF) Priority Queuing

Replay rtp packets marked with vlan 30 pcp 5 dscp 46 through switches and SD-WAN edges to confirm voice media lands in strict-priority queues without DSCP bleaching.

Simulate Packet Loss, Out-of-Order & Jitter in Wireshark RTP Analysis

Intentionally skip an RTP seq number (for example 1, 2, 4) or vary wait (20ms, 65ms, 5ms) to validate packet-loss and jitter alarms in VoIP monitoring probes.

Multicast Paging & Broadcast IPTV Stream Labs

Send rtp pt 96 streams to a 239.x.x.x multicast host alongside igmp joins.

Minimal Quickstart (rtp_quickstart.frasm)

Hit Preview Packets to compile in-browser and eyeball timestamps + wire byte lengths, or ship it straight to the Playground.

rtp_quickstart.frasm8 lines
Open in Playground
host handset_a { ip 10.30.1.101 }
host handset_b { ip 10.30.1.102 }
compile {
handset_a -> handset_b rtp pt 0 seq 1 timestamp 160 ssrc 0x12345678 marker 1 dscp 46 payload "frame-1" wait 20ms
handset_a -> handset_b rtp pt 0 seq 2 timestamp 320 ssrc 0x12345678 marker 0 dscp 46 payload "frame-2" wait 20ms
handset_a -> handset_b rtp pt 0 seq 3 timestamp 480 ssrc 0x12345678 marker 0 dscp 46 payload "frame-3"
}

What the Compiler Calculates So You Don't Have To

  • Defaults to UDP destination port 5004 and writes RTP Version 2 (0x80) in the upper bits of byte 0.
  • Packs the 1-bit marker and 7-bit Payload Type (pt) cleanly into byte 1 ((marker << 7) | pt).
  • Treats seq on an rtp line as the 16-bit RTP header Sequence Number.
Multi-Frame Lab · Ready to Compile

G.711 VoIP Stream With Simulated WAN Jitter & Single-Packet Drop

Emits a G.711 PCMU (pt 0, 8 kHz = +160 timestamp ticks per 20ms) voice burst containing a skipped sequence number (seq 3 dropped) and a 55ms jitter spike.

rtp_qos_jitter_lab.frasm11 lines
Open in Playground
host branch_phone { ip 172.16.30.21 }
host hq_gateway { ip 172.16.1.10 }
compile {
// Normal 20ms pacing (+160 samples at 8000 Hz)
branch_phone -> hq_gateway rtp srcport 16384 dstport 16400 pt 0 seq 1 timestamp 160 ssrc 0xdeadbeef marker 1 dscp 46 payload "audio-pkt-1" wait 20ms
branch_phone -> hq_gateway rtp pt 0 seq 2 timestamp 320 ssrc 0xdeadbeef marker 0 dscp 46 payload "audio-pkt-2" wait 55ms
// seq 3 intentionally omitted to test 1-packet loss + 55ms jitter detection!
branch_phone -> hq_gateway rtp pt 0 seq 4 timestamp 640 ssrc 0xdeadbeef marker 0 dscp 46 payload "audio-pkt-4" wait 5ms
branch_phone -> hq_gateway rtp pt 0 seq 5 timestamp 800 ssrc 0xdeadbeef marker 0 dscp 46 payload "audio-pkt-5"
}
Terminal Commands (FrameAssembly CLI v3.1.2)
# 1. Eyeball relative timestamps, ports & wire lengths in your terminal
frameassembly show rtp_qos_jitter_lab.frasm

# 2. Compile .frasm -> classic .pcap (tcpdump/tcpreplay/Suricata) or nanosecond .pcapng
frameassembly rtp_qos_jitter_lab.frasm rtp_qos_jitter_lab.pcap
frameassembly rtp_qos_jitter_lab.frasm rtp_qos_jitter_lab.pcapng

# 3. Round-trip .pcap <-> .frasm whenever you want to scrub or tweak an existing capture
frameassembly reverse rtp_qos_jitter_lab.pcap rtp_qos_jitter_lab_edited.frasm

All rtp Keywords & Header Options

Every sub-keyword and header option is lowercase [a-z0-9]+ with zero underscores — mix and match them in any order after rtp:

src_host -> dst_host rtp [pt <0..127>] [seq <0..65535>] [timestamp <number>] [ssrc <hex_or_num>] [marker <0|1>]
Keyword / OptionAccepted ValueDefaultEffect on Packet
pt <0..127>7-bit RTP Payload Type (0 PCMU, 8 PCMA, 9 G.722, 96 Opus/H.264, 101 DTMF)0 (G.711 PCMU)Sets the lower 7 bits of byte 1 in the 12-byte RTP header.
seq <0..65535>16-bit RTP Sequence Number1Sets bytes 2..3 of the RTP header used by receivers to detect packet loss and reordering.
timestamp <number>32-bit media sampling clock timestamp160Sets bytes 4..7 of the RTP header (+160 per 20ms for 8kHz voice; +1800 per frame for 90kHz 50fps video).
ssrc <hex_or_num>32-bit Synchronization Source ID0x12345678Uniquely identifies the unidirectional RTP media stream in bytes 8..11.
marker <0|1>1 (talkspurt start / end-of-video-frame) or 00Sets the 1-bit M flag at the top of byte 1.

Cross-Layer Wrappers Valid with rtp

802.1Q VLAN / QinQ / MPLS tags, IPv4/IPv6 QoS & TTL fields, wait gaps, and transport overrides allowed on this protocol

10 options
OptionRange / FormatDefaultEffect on Packet
wait <number><ns|us|ms|s|m>Time gap (ns, us, ms, s, m)10msAdvances the packet timestamp clock after sending this packet and before the next packet (wait 0ns sends back-to-back).
payload "<text>" | hexpayload "<hex>"Quoted text or hex bytes (choose one)OmittedAppends or overrides raw payload bytes ("deadbeef" or "de:ad:be:ef") and updates packet lengths and checksums.
srcmac <mac> | dstmac <mac>Colon, hyphen, or Cisco dot MACHost MAC / RFC multicast MACOverrides the 14-byte Ethernet II source or destination MAC address for this single packet.
vlan <0..4095> [pcp <0..7>] [dei <0|1>]VLAN ID 0..4095, PCP 0..7, DEI 0..1UntaggedWraps the packet in an IEEE 802.1Q VLAN tag (0x8100) with optional 802.1p QoS priority.
qinq <0..4095> [innervlan <0..4095>]Outer S-VLAN 0..4095, Inner C-VLAN 0..4095Untagged (innervlan 1 when qinq is set)Double-tags the packet with outer IEEE 802.1ad S-Tag (0x88a8) plus inner IEEE 802.1Q C-Tag (0x8100).
mpls <0..1048575> [exp|tc <0..7>] [bos <0|1>] [mplsttl <0..255>]Label 0..1048575, exp/tc 0..7, bos 0..1, ttl 0..255Unlabeled (at most 1 mpls tag per packet)Inserts a 32-bit MPLS label header (0x8847) ahead of the Layer 3 header.
ttl <0..255> [dscp <0..63>] [ecn <0..3>]TTL/Hop Limit 0..255, DSCP 0..63, ECN 0..3ttl 64, dscp 0, ecn 0Sets IPv4 TTL or IPv6 Hop Limit plus DiffServ (DSCP) and ECN QoS markings.
ipid <0..65535> [df] [mf] [fragoffset <0..8191>]IPv4 ID, DF/MF flags, fragment offset 0..8191ipid 1, flags 0, fragoffset 0Sets IPv4 Identification, Do-Not-Fragment (df), More-Fragments (mf), and fragment offset (ignored over IPv6).
flowlabel <0..1048575>20-bit IPv6 Flow Label (0..1048575)0Sets the 20-bit IPv6 Flow Label for ECMP routing tests (ignored when running over IPv4 hosts).
srcport <0..65535> | dstport <0..65535>Port number 0..65535srcport 49152 (remembered), UDP 5004Overrides source or destination port and remembers the port pair automatically on <- replies.

Gotchas & Quick Fixes

Enable Wireshark "Try to decode RTP outside of conversations" for Standalone RTP Captures

Valid v3.1.2 Syntax
Pair rtp with sip invite + SDP, or enable RTP heuristic dissection in Wireshark

Because RTP uses dynamic even UDP ports without a fixed magic header, Wireshark auto-detects RTP when preceded by sip / rtsp setup—or on any UDP port when *Analyze -> Enabled Protocols -> rtp_udp* is checked.

pt Maximum Value Is 127 (7 Bits)

Avoid
handset_a -> handset_b rtp pt 200
Valid v3.1.2 Syntax
handset_a -> handset_b rtp pt 96

The RTP Payload Type shares byte 1 with the 1-bit marker flag, so pt must be 0..127.

Field Guide 05
VLANs, QinQ, MPLS, Tunnel Soup & Dual-Stack IPv6